Glastron Carlson CV 19 SS (1974)

Our technical section for all matters related to the care, maintenance and restoration of your classic boat.

Moderators: Alacrity, Rapier

Re: Glastron Carlson CV 19 SS (1974)

Postby broompisces » Tue Jul 12, 2011 10:54 pm

I know what you mean about using nice shiny screws to fill the holes - unfortunately, some of the holes are the size of 50 pence pieces! I've had a go at chrome blanking plates for taps on sinks, but it doesn't look right.

I'd be obliged for the details of the paint supplier in the US if you can contact the chap that bought your boat.

My paint is the "apricot" one - like a metallic bronze. See the snap below for an idea of the colour.
cv 19 gel.jpg
Posts: 126
Joined: Tue Feb 17, 2009 8:20 pm
Location: Glasgow, Scotland

Re: Glastron Carlson CV 19 SS (1974)

Postby Rapier » Wed Jul 13, 2011 8:24 am

Sent you a PM, hope it helps..
Fasten bra straps and remove dentures...
User avatar
Posts: 9534
Joined: Thu Feb 05, 2009 5:16 pm
Location: South Coast

Re: Glastron Carlson CV 19 SS (1974)

Postby fisco » Thu Aug 08, 2013 10:35 am

Any updates on this beauty?
1977 Almarine Meteor Jetboat Restoration
Posts: 41
Joined: Mon Jul 20, 2009 6:28 pm
Location: Shropshire

Re: Glastron Carlson CV 19 SS (1974)

Postby broompisces » Wed Jan 04, 2017 4:30 pm

It's been a while...
I'm now getting ready to start the refurbishment in earnest.
I need to get the boat re-painted in the metal-flake paint (an old english white for the hull).
Does anyone know of a yard that has experience with painting using metal-flake? I've been on many USA websites / forums and they seem to follow very complex (to me!) processes when using metal-flake. Also, they have different opinions about preparation etc.
I'll travel within the UK to get the right job done.
Many thanks,
Posts: 126
Joined: Tue Feb 17, 2009 8:20 pm
Location: Glasgow, Scotland

Re: Glastron Carlson CV 19 SS (1974)

Postby se7en » Wed Jan 04, 2017 7:27 pm

I've sprayed Metal flake, back in the 70s when it was in fashion, never had a problem , use a under cup gun, put some ball bearings in it to keep the flakes in suspension, use a large nozzle, any good paint sprayer should be able to get there head round it , there's no difference in the prep, with some flake colours , it is recommended that a base colour is put down first, a lot of the darker gold, blue and green colours went over a black base colour, the lighter gold, silvers, reds went over light grey or white. the secret is to use a top quality clear lacquer .
Posts: 601
Joined: Fri Feb 06, 2009 7:25 pm
Location: Burnham-on-Crouch

Re: Glastron Carlson CV 19 SS (1974)

Postby pspeed » Fri Jan 20, 2017 9:12 am

I agree with the above,

I have also sprayed Metalflake "back in the day" and the base coat colour and gun needle / tip size are key to it all.
If the gun set up is too small the nozzle (paint tip) will clog all the time, also the base colour should be pretty close to the flake colour.

In my inexperience as a lad I once sprayed a beach buggy with blue flake over a purple base coat which looked OK but you could definitely see it through the flake.

Also be prepared for how much laquer it will take to cover it properly (hint,- it's a lot) so you'll probably need to lacquer over the white as well to avoid a raised edge once the tape is removed.

Any decent sprayer should be able to do it.

Posts: 59
Joined: Thu Mar 17, 2011 11:02 am
Location: Falmouth

Re: Glastron Carlson CV 19 SS (1974)

Postby De Novo » Wed Nov 15, 2017 1:03 am

I wondered how your Glastron project was coming along. I have just brought a Glastron SSV - 153 project, 1978 and I am pretty sure, built here in the U.K. by Roger Clark Marine. It is white with Metalflake silver stripes and gives me the same headache; gelcoat repair or respray. My Metalflake sections are the original 'moulded in' method, so I will try to leave it original. Are yours moulded in or sprayed on? I will decide on my method once the 'breakdown' of the boat has been completed. I had a Kawasaki KH400 motorbike sprayed in black Metalflake when I was a teenager. To get the same depth of gloss on our boats as original it would take many coats if lacquer over the paint. Remember also there were, in the 70s, two sizes of Metalflake - 'Medium' and 'Extra Brilliant' available in all the colours, so we would need to know which type we need. I have the original Metalflake paint colour sample card somewhere, and is on my job list as something to find.

De Novo
Posts: 23
Joined: Tue Sep 08, 2015 3:15 pm


Return to The Boatshed

Who is online

Users browsing this forum: No registered users and 4 guests